Install Connector Cable Network

To install an RJ-45 connector on the cable UTP There are two types of installation:

Type straight and Type cross

1. Type straight

is used to connect a computer to the hub / switch hub

The order of installation:

Standard A:

A tip of the tip B

1. Green White

2. Green

3. Orange White

4. Blue

5. Blue White

6. Orange

7. Brown White

8. Brown

1. Green White

2. Green

3. Orange White

4. Blue

5. Blue White

6. Orange

7. Brown White

8. Brown

Standard B:

A tip of the tip B

1. Orange White

2. Orange

3. Green White

4. Blue

5. Blue White

6. Green

7. Brown White

8. Brown

1. Orange White

2. Orange

3. Green White

4. Blue

5. Blue White

6. Green

7. Brown White

8. Brown

2. The type of cross / cross

specifically to connect two computers directly without using a hub / switch hub. For now cross type can be used to connect a computer to the hub. The latest Hub own auto sense so that it can detect the type of cable attached.

The order of installation:

One end is fitted with Standard A and the other end is fitted with a standard B, it will be a cross cable

A tip of the tip B

1. Green White

2. Green

3. Orange White

4. Blue

5. Blue White

6. Orange

7. Brown White

8. Brown

1. Orange White

2. Orange

3. Green White

4. Blue

5. Blue White

6. Green

7. Brown White

8. Brown

kabel4

the sequence begins pin no.1 leftmost position the hole on RJ-45 connectors facing us and a key hook located on the bottom side

Tools and materials :

1. UTP Cables

2. RJ-45 Connector 2 pieces

3. Tank Crimping

4. UTP Cable Tester (let me know if any of nyambungnya)

Work steps :

Step 1:

Exfoliate outer UTP cable along approximately 2 cm with a knife pliers krimping thus appears inside wiring totaling 8 units,

Step 2:

Sort and trim wires in accordance with

color below:

1. Green White

2. Green

3. Orange White

4. Blue

5. Blue White

6. Orange

7. Brown White

8. Brown

Step 3:

Cut the ends of the cable neatly together so sehigga lined with flat ends

Step 4:

Insert the end of last UTP cable into the RJ-45 connector. Make sure the order is correct in accordance with the lines that have been provided in the last connector.

And also make sure the ends of each cable is fixed inside the RJ-45 connector

Step 5:

Enter RJ-45 connector that has terpasangi earlier UTP cable to one of the crimping pliers mouth that has a shape and size compatible with RJ-45 connectors. Press the base of the connector with pliers krimping. Emphasis will make pin-pin connector on the other end embedded in each cable.

do steps 1 s / d 5 for both ends of the cable

Step 6:

Test with a cable tester. Plug one end into the parent tester (big mouth) to the Tx port. And plug the other end to child tester (small mouth) to the Rx port. Turn on the cable tester by sliding the switch to the auto position.

in tester Parent:

The indicator lights in sequence of indicator lights 1 s / d 8 and G (ground)

Notice in the tester children:

If the indicator light also lights on the parent position indicator light turns on, then the cable is no problem.

If the indicator light is illuminated on the master tester specific numbers while the indicator lights on the tester on the number of children is not lit, wired with color is experiencing problems.

If the indicator light is illuminated on the master tester specific numbers while the indicator lights on the tester lights up children at another number sequence bearti improper installation. (Except for the kind of cross)

Problems that may arise:

Cable break in the middle

quality connectors are less good

installation is not good, ie no edge kanel are not stuck inside the connector so it is not plugged by the pin connector